10 Tried-and-True Methods for Building an Off Grid Water Pump System

Last Updated on

Water is a commodity that we tend to take for granted when living off a municipal source.

Once we take the plunge into going off grid, it becomes the primary concern.

Where will the water come from? How will we get the water from source to home? How will we filter and purify the water?

Although the internet is packed with information, I have found that there is only a patchwork of pieced information that isn’t very substantial to designing an independent water system.

I have written a series of articles that helps pull all the pieces together so you can make the best design for your off grid system.

In this article, I delve into the various types of off grid water pumps that you can utilize to setup an off grid water system. 

If just starting on your off grid water system journey, I suggest reading my Off Grid Water System Guide which covers the different types of water sources and how to get that water to your home.

Let’s get started!

A vintage water pump!

Types Off Grid Water Pumps

Off Grid Well Pumps

Wells are often the best choice for fetching water on a homestead. Wells are rather expensive but can last for several decades and can withstand through winters and times of drought.

Wells can be professionally installed or do-it-yourself. If you do decide to dig your own well, you will have to rent special equipment.

Some homesteaders choose to dig a homemade shallow well, possibly a few feet away from a water source on the property. Shallow wells have a higher chance of being contaminated, so make sure to filter and purify your water correctly.

Check out my handy guide to off grid water filtration and purification.

A crude homemade shallow well 

1. Shallow Well Jet Pump

A shallow well jet pump is not placed directly into the well, rather it is placed above the well and pulls the water up from the well using suction. This suction creates a vacuum that automatically pulls the water up much like how a straw does. Once the suction is made, the atmospheric pressure pushes the water up and becomes an autonomous system.

A shallow well jet pump is just for that – shallow wells. It is limited to how high it can lift the water in relation to the pressure of the air. Therefore the depth maximum is usually 25 feet. These pumps also require to be primed with water to work. A foot valve is optional but is a typical component on shallow pumps to avoid water from backing out.

2. Deep Well Jet Pump

The deep well version of the jet pump is similar to the shallow pump setup. The pump sits above the well and works in the same way as the shallow version. However, the ejector component is separated from the pump and is placed deep into the well to push the water up to the pump.

A deep well jet pump can be used for a depth of around 200 feet (depending on altitude) yet can be accessed easily if it ever needs servicing. A foot valve is used at the bottom of the well pipe so water does not drain back out. The deep well jet pump also needs to be primed before use.

3. Convertible Jet Well Pump

A convertible jet well pump is a deep well pump that can be altered for both shallow and deep wells.

An ejector assembly is used to convert the pump from shallow to deep. You can use a convertible pump for pulling water from streams, lakes, and rivers; you can then convert it into a deep well pump for depths over 25 feet.

This could be a good solution if you are using a temporary water source before installing a deep well. This will save you the cost of having to purchase a new pump down the road.

A Note on Jet Pump Systems

Due to the nature of pulling water as opposed to pushing water, above ground pumps tend to have a higher rate of breakdowns and failures.

If the pump loses its prime it will cause the motor to burn out. This is why many well owners choose the submersible pump.

4. Deep well submersible pump

This type of centrifugal pump is lowered all the way into the well and pushes the water instead of pulling it up. This pump fits into the well casing and is connected to an above-ground power source with wires. 

The motor is sealed to prevent water from short-circuiting the pump. A submersible pump must always be submerged in water in order for it to work.

The submersible well pump needs to be sized in accordance with the peak needs of your water usage and the water yield of the well. Never go beyond pumping more than what your well can produce unless you have a storage of water to supplement it.

Submersible pumps have a long shelf life; you can expect your pump to last up to 25 years. They typically have fewer problems than above ground pumps and will last as long as they are fully submerged in water. 

If the pump does break, it will have to be pulled out of the well to be serviced which usually calls for a professional.

5. Hand Well Pump System

Having a manual hand well pump system on your property isn’t a bad idea for a backup water source. A hand pump requires no electricity and are extremely reliable.

A hand pump system comprises of very little parts; a cylinder that is placed within the dug well, a piston, two valves, water, and air.

When the lever is pushed down, the piston goes below the spout level which shuts off air flow. The lower valve then opens which draws the water up into the cylinder.

When the lever is pulled up, the lower valve closes which traps the water in the cylinder, and air flow is opened which raises the water up more.

The pushing and pulling of the lever raises the water until the water comes gushing out of the spout.

There has been a trend of installing antique water pumps, so the demand of these pumps has risen. You can find authentic ones on eBay or purchase a replica.

A hand well pump probably won’t be your primary source of water but could be a nice supplement for filling water troughs and watering the garden. 

Off grid pumps for lakes, rivers, and streams

When pumping from a natural source of water on your property, you need to consider the distance the water has to travel and the rise from the water source to the destination.

Now, if your water source is uphill from the destination, you are in luck. You may be able to use gravity in replacement of a pump!

For the rest of us, we need to choose a correct off grid water pump that will work for pushing water from a downhill water source without burning up the pump. 

Most wild water sources will be downhill from the destination.

1. Shallow Well Jet Pump

Jet pumps are very powerful as they are used to vertically lift water out of a well.

These pumps work great for sucking water from a downhill water source and can be used to push water on a slope for a good distance.

You can dig a makeshift well right next to a water source and place the shallow well jet pump on a platform next to the sump hole. Then lower in the attached piping into the hole.

Make sure to use some sort of filtration screen enclosure at the end of the submerged piping so it doesn’t get clogged with debris.

Note that jet pumps are installed on dry ground and need to be primed before use.

2. Submersible Sump Pump

A submersible sump pump is a great option for pumping water from the wild into your water system.

Wayne Waterbug sump pump in the grass

Since sump pumps work by pushing water instead of pulling, you can get a decent amount of pressure to make it up an incline.

When you purchase a submersible sump pump, make sure to check the gallons per minute by feet of head, as the deeper the pump is lowered into the water, the less GPM you will get.

Dig a sump hole next to a water source and line with large rocks, then lower in your submersible sump pump. Make sure to build a screen enclosure to filter out debris.

 

Example of a sump pit dug by water source

A submersible pump is a nice option as you can easily relocate the pump to different areas of the water source, a good feature if your water source changes depth and shape. 

Make sure to add a filter around the pump so you are not sucking up debris into your piping.

I have written an extensive guide on the Best Submersible Sump Pumps to help you make an informative and smart purchase decision.

3. Marine Bilge Pump

A marine bilge pump may not be the first kind of pump you would think of for this task, but they are extremely powerful and durable for outdoor applications. They are also very reliable.

A bilge pump is designed to pump large amounts of water very quickly as they are used to get water out of a (sinking) boat!

Bilge pumps can pump out a tremendous amount of water to the tune of thousands of gallons per hour, however, they are designed for very little head (the rise of the water) so pumping uphill with a bilge pump will be less effective.

You can expect a bilge pump to handle 0 – 25 feet of rise depending on the model.

This pump could be good for moving massive amounts of water from one location to another. A possible use case is if you need to get your water from a far location to a holding sump pit near your destination. 

Special Note on Pumping Wild Water

do not use a garden hose for your suction line as it will likely flatten out and stop the flow.

The diameter of a garden hose will not be big enough and can stifle the output of the pump. Go with at least 1” PVC pipe or specially designed suction hose.

Make sure the water is filtered of large debris before sucking it through your pipe system. This can be done with a homemade screen filter or a prefabricated one.

Pumps for storage tanks

A water storage tank can come in various shapes, sizes, and depths, and types. There are tanks for hauling water, underground cistern tanks, and rainwater collection barrel tanks.

A cistern water system is a good choice for properties that do not have enough water production year-round but have enough water for partial support. 

The tank can hold any excess water from the source be it a low producing well or seasonal stream. If water needs cannot be met, then additional water can be hauled in and stored in the cistern.

There are pumps specially designed to pump water from cisterns to the desired destination.

1. Cistern submersible pump

This pump is specially designed for a cistern and is lowered all the way to the bottom.

The pump is designed to suck in water from the bottom side of the pump so the cistern can be almost completely emptied, although an underground cistern should not be emptied entirely.

The pump does not need any casing and can be dropped in as-is.

2. Shallow well cistern pump

A shallow well jet pump works as a great option for pumping water out of a cistern.

Note that the elevation of the pump and the inlet pipe running to the pump should be very similar in elevation.

If there are any high spots between the cistern and the pump, it can cause an air bubble that prevents flow.

The pump can be installed at a lower elevation than the cistern.

Special Notes on Cistern Pumps

You will need to install additional components when using a cistern as your main water source. A check valve, pressure switch, and water pressure tank, respectively.

A check valve allows the water to flow in one direction and keeps the water from backflowing into the system. If there is no pressure switch on your pump, then the check valve needs to be installed between the cistern and the pressure tank, typically at the outlet of the cistern. If there is a pressure switch on the pump, then install the check valve at the inlet of the pump.

The pressure switch turns your water pump on or off when it reaches certain pressures. The pump is turned on at around 20 – 30 PSI and is turned off at 40 – 50 PSI. Many pumps have a pressure switch installed on the unit.

A water pressure tank does just that, provides pressure to the water. A pressure tank works by creating water pressure from compressed air that bears down on the water. When the valve gets opened, the water is forcefully pushed from that air in the tank. Once the pressure drops to a certain low, the tank’s water pump turns on and more water fills the tank; this is the cycle of the pressure water tank.

You can check out my pressure tank sizing instruction in my guide to building an off grid water system

Go Pumpless! Gravity Water Systems

Harness the law of gravity and eliminate your need for a pump! If your water source is located uphill from your water destination, or if you have a nice hill that you can place your water tanks, then you may be able to remove your need for a pump entirely.

There is a simple equation for figuring out how much pressure you get from elevation. Each foot of elevation change amounts to .433 PSI of water pressure. The typical pressure for home usage is around 40 – 45 PSI. Therefore, 100 feet of elevation (or feet of head) could provide enough pressure for a homestead without the use of a pump.

100 feet seems like a lot but carried out over a slope or hill, the elevation can add up fast.

Note that this calculation is based upon static pressure of water, such as still water from a tank or a deep water hole. If the water is flowing, this creates dynamic pressure and the system would actually lose pressure due to friction on the sides of the pipe.

I hope you have found my off grid water pumps guide to be informative and helpful in your water system setup!

Please share this article and leave any comments or questions! Thanks!

Hello, I am Regina! I am the creator and brain-child behind Maximum Off Grid. 

My goal is to educate and inform people interested in becoming independent from the system. 

I also provide valuable reviews on products and service that I research thoroughly and make quality  recommendations.

I hope you are enjoying my website!

Regina C. 
Creator of Maximum Off Grid
  • 8
  •  
  •  
  •  
  •  
  •  
  •  

Leave a Comment